Skip to content

Trade takeoff

How to take off a roof from plans

How to measure a residential roof from the drawings — roof area, sheet quantities, battens, fascia and gutters, and the pitch factor that changes everything.

Insights Published · 9 min · By Scaleline

For Australian builders of new homes.

Timber roof trusses framed over an unfinished house.

To take off a roof from plans, read the roof plan for the footprint and the sections for the pitch, then work the sheet quantities off the net roof area, not the flat plan area. A roof is where the flat drawing and the real building diverge most, and the pitch is the reason. Here’s the order we work in.

Start from the roof plan, then apply the pitch

A roof plan measuring pass begins with the roof plan itself, because that’s where the outline, the hips and valleys, and the sheet direction are shown. But the roof plan is drawn in plan view — flat — and a roof isn’t flat. Before you can measure anything in area, you need the pitch off the sections or the elevations, and you apply it to every sloped surface.

Work out the plan area of each roof face from the roof plan, then convert each face to its true sloped area using the pitch factor for that face. A face at a different pitch — a steeper skillion over one wing, a flatter verandah roof over another — gets its own factor, because the difference between plan area and true area grows with the pitch. Treating the whole roof at one pitch when the sections show two is the single most common roof quantity error.

The eaves overhang matters too. Measure to the outside of the roof, including the eave, not to the outside of the wall, because the roof covers the eave and the sheeting runs to the fascia.

Sheet quantities from the net roof area

The roof sheeting quantities come off the true sloped area, less nothing at first — then you deduct for what the sheeting covers and add for what it doesn’t. Metal roofing is priced by the sheet length and the number of sheets, so the quantity is driven by the area and the sheet profile’s cover width.

Take the true roof area per face, then work out sheet runs by dividing the slope length by the sheet length, accounting for the sheet cover width to get the sheet count. Skylights, penetrations and any flashings around a chimney or a vent reduce the sheet area but add their own line items — a flashing is a cost, not a saving, so it comes back as a separate line rather than a simple deduction.

The waste on sheet ends and at hips and valleys is a real allowance on a metal roof, and it’s worth keeping visible. A roof with a lot of hips and valleys will carry more sheet waste than a simple gable, so the allowance changes with the roof shape.

Battens, fascia, gutters and other linears

Once the area is done, the roof is mostly a series of linear items. Battens run across the rafters at a set spacing, so they’re measured in linear metres per roof face — the sloped area divided by the batten spacing, or the rafter length times the number of battens. Read the spacing off the roofing specification, because it changes with the sheet type and the wind region.

Fascia and gutter run around the roof perimeter, so they’re linear metres off the roof plan’s edge, including the gable ends and any skillion edges. Downpipes are a count per downpipe, with the length read off the elevations. Barges run up the gable ends. Each of these is a separate line, and each is measured in a different unit, which is why a roof take-off that only produces an area is only half done.

Hips, valleys and the pitch factor

A roof take-off from plans isn’t complete until the hips, valleys and ridges are counted as their own lines. A hip and a valley are both linear, measured along their true length, which again comes off the pitch — the ridge length is straight off the plan, but a hip or valley runs on the slope, so its true length is longer than the plan view shows.

Cappings and flashings run along the hips and ridges as their own linear items. On a cut-and-pitched roof the rafters, ridge and valley boards are all counts and lengths off the roof framing plan; on a trussed roof the truss schedule gives you the truss count per type, and the roof framing plan gives the truss layout to count them against.

The pitch factor is worth stating out loud here: the steeper the roof, the more the true lengths and areas exceed what the plan shows. A builder who measures a steep roof off the flat plan is quietly under-ordering on every line that follows the slope.

Trussed and cut-and-pitched roofs also take off differently. A trussed roof comes with a fabricator’s truss schedule, so the roof structure is a count of trusses per type against the truss layout, plus the bracing shown on the roof framing plan. A cut roof has no schedule — you count the rafters per slope, the ridge and the valley boards by length, and the underpurlins and struts off the roof framing details. Mixing the two methods, or measuring a trussed roof as if it were cut, produces a structure quantity that matches neither the fabricator nor the carpenter.

The details that add up on the invoice

The roof is where the small items accumulate. Sarking runs under the battens and is measured by the roof area. Insulation blanket runs over the ceiling, not the roof. Flashings around the chimney, the vent penetrations and the plumbing risers are all separate items read off the details. The gutter clips, the batten fixings and the sheet screws are usually carried in the rate, but only if the spec says so — if the specification calls them out separately, they’re lines.

A box gutter is the item that changes a roof take-off most when it appears. It’s measured in linear metres with its width and depth, it needs its own flashing and overflow, and it’s often drawn on a detail that sits apart from the roof plan. Because a box gutter only turns up on certain roofs — flat sections, parapet walls, complex junctions — it’s the kind of line that’s easy to miss until the plumber’s invoice lands, and it’s worth a dedicated pass of the details looking for one.

Read the wind region off the roof notes, because it changes the batten spacing, the sheet gauge and the fixing schedule. That’s an Australian detail that matters: the same roof shape measures differently in a different wind region, so the location isn’t a nicety, it’s a quantity driver.

How we measure a roof

Our engine reads the roof plan’s vector and text layers first — the sheet direction, the plan dimensions and the pitch callouts the drafter wrote down — and uses vision only to resolve what the annotations leave out, like a penetration drawn but not called out. Every roof line in the report carries its source sheet and dimension, plus a confidence mark, and anything uncertain is checked by a local estimator before it ships.

You can see a worked roof line in our sample report, and read the reading-and-checking mechanism behind it on our method page. To verify our numbers against a roof you’ve already built, book a blind test →.

This is Scaleline’s view. We measure residential jobs from drawings — we don’t price them, and we don’t sell software. Where we mention how we work, it’s to be useful, not to oversell.

See it on your own job

A roof is where the flat plan and the real building diverge. Test us on a roof you’ve already built and check our numbers.