Trade takeoff
How to take off wall framing from plans
A practical guide to measuring wall framing from residential drawings — studs, plates, lintels, bracing and the openings that change every count.
Insights Published · 9 min · By Scaleline
For Australian builders of new homes.
To take off wall framing from plans, read the wall schedule and the floor plan together, count the studs and plates in linear metres, then add the lintels, trimming studs and bracing that every opening forces into the job. Framing is a trade where the plan gives you almost everything you need, but only if you count it in the right order. Here’s the order we use.
Start from the floor plan and the wall schedule
A wall frame take-off starts with two documents, not one. The floor plan gives you the wall lengths and openings; the wall schedule gives you the section — stud size and spacing, plate size, and any specific bracing. Reading one without the other is how a framing quantity ends up looking plausible and being wrong.
Measure the total wall length in linear metres off the floor plan, wall by wall, and keep each wall on its own line so it can be checked. The plates run the full length of every wall, so plates are just wall length times two — top and bottom plate — plus any additional top plates the schedule calls for. Then work through the openings, because every window and door changes the count that follows.
Framing quantities are only as good as the wall schedule you read them from. If the schedule says 90mm studs at 450 centres, count that; if it says 450 centres on load-bearing walls and 600 on non-load-bearing, you now have two different counts and they need to stay separate.
Studs, plates and noggins from the schedule
The framing quantities from plans come out cleanest when you separate them by what they are. Plates are linear metres. Studs are a count. Noggins are a count driven by wall height and stud spacing.
For studs, work out the count per linear metre from the spacing, then multiply by the net wall length — gross wall length less the openings, because a stud doesn’t run through a window. Add the studs at each corner, each intersection and each end of a wall, because those are extra studs that the simple per-metre count misses. That’s the number most hand take-offs undercount, and it’s the number that shows up as short studs on site.
Noggins come off the stud height: the number of rows is a function of wall height and the schedule’s bracing or fixing requirements. If the drawings specify a noggin row at a particular height, that’s a count per wall length, not a guess.
Openings: lintels, trimming studs and jack studs
Every window and door opening adds more than a hole. It adds a lintel across the top, trimming studs either side, and a sill trimmer below a window. These are all separate lines and they’re all driven by the opening size, which you read off the schedule rather than scaling off the drawing.
For each opening, read the lintel size off the lintel schedule — a wider opening takes a deeper or heavier lintel, and the size changes the rate. The trimming studs are a count per opening side. The jack studs under the lintel ends are another count. Multiply each by the total number of openings of that size and you have the opening lines done.
Openings are also where framing meets other trades. A window opening with a header that needs a steel angle instead of a timber lintel is a different line again, and it’s the kind of detail that’s easy to carry in your head and lose between the plan and the price.
Timber vs steel: what changes in the take-off
A timber frame take-off and a steel-frame take-off look similar on paper but diverge in the units and the details. Timber is counted in linear metres and stud counts; steel is often driven by a frame schedule from the fabricator, with members given as discrete lengths and a part reference.
With timber you carry the section — 90x45 versus 70x35 — because it changes both the rate and the bracing. With steel you carry the member designation and the length, and you rely on the fabricator’s schedule far more than you would for timber. The openings and the bracing still matter in both, but the way the count is expressed changes.
The practical point is to keep the two systems separate in a mixed job. Some houses have a timber upper level over a steel or masonry lower level, or steel portal frames where a wall has been opened up. Each system gets its own section of the take-off, because the people pricing them are usually different.
Waste, wall height and the details that add up
The small framing items are where the hours and the errors hide. Wall height changes between a 2.4m stud and a 2.7m stud, and it changes stud length, sheet length and bracing. A split-level or a raked ceiling means not every wall is the same height, and treating them as if they are is a fast way to a light quantity.
Bracing deserves its own reading pass, because it’s driven by the wind region and the wall’s position in the building, not by the stud count. The bracing plan shows the panels and straps, and the wall schedule shows the fixings; a corner or a long straight wall takes different bracing to a short internal wall, so the bracing quantity can’t be inferred from the wall length alone. Reading the bracing off the bracing plan, rather than estimating it off the floor plan, is what stops the frame passing the wall check and then failing on site.
On the allowance side, timber framing carries a wastage factor on studs and plates, and it’s worth keeping as a visible line rather than folding it into the rate. Keep the bracing as its own line too — plywood or strap bracing is measured in lineal or sheet terms off the bracing plan, and it’s frequently the line a quick take-off skips entirely.
Prefabricated wall frames change the shape of the job. When the walls arrive as factory-made panels, the take-off shifts from studs and plates to a count of panels by wall, with the frame schedule giving the part references. The openings, bracing and lintels still matter — they’re just delivered inside the panels instead of cut on site — so the quantity you hand over becomes a panel list rather than a timber list, and the two should never be mixed in the same section of the report.
How we measure wall framing
Our engine reads the wall schedule and the floor plan’s vector and text layers first — the stud sizes, centres and wall dimensions the drafter wrote down — and uses vision to resolve only what the annotations leave out, like a bracing panel that’s drawn but not called out. Every framing line in the report carries its source sheet and dimension, plus a confidence mark, and anything uncertain is checked by a local estimator before it ships.
You can see a worked framing line in our sample report, and read how the reading-and-checking mechanism works on our method page. If you’d rather verify our numbers against a job you’ve already built before you commit anything, book a blind test →.
This is Scaleline’s view. We measure residential jobs from drawings — we don’t price them, and we don’t sell software. Where we mention how we work, it’s to be useful, not to oversell.